"C/M" indicates both monochrome and color sensor options are available for this part number. Full part numbers are available here http://www.ptgrey.com/sales/models.asp.
|
SPECIFICATION |
FFMV-03M2M/C-CS
|
FMVU-03MTM/C-CS
|
FMVU-13S2C-CS (Color only) |
| Image Sensor Type |
1/3” progressive scan CMOS |
| Shutter Type |
Global shutter using Micron TrueSNAP™ technology |
Rolling shutter |
| Image Sensor Model |
Micron MT9V022 |
Sony IMX035LQR-C |
|
Maximum Resolution |
752 (H) x 480 (V) |
1328 (H) x 1048 (V) |
|
Pixel Size |
6.0 µm x 6.0 µm |
3.63 µm x 3.63 µm |
|
Analog-to-Digital Converter |
On-chip 10-bit ADC |
On-chip 10 / 12-bit ADC |
|
Video Data Output |
8 and 16-bit digital data |
|
Image Data Formats |
Y8, Y16 (monochrome), 8-bit and 16-bit raw Bayer data (color models) |
|
Digital Interface |
6-pin IEEE 1394a for camera control, video data, power |
5-pin Mini-B USB 2.0 for camera control, video data, power |
|
Transfer Rates |
400 Mb/s |
480 Mb/s |
|
Maximum Frame Rate |
752x480 at 60 FPS
320x240 at 112 FPS (region of interest)
320x240 at 122 FPS (2 x 2 pixel binning) |
Free-running acquisition: 1328x1048 at 23FPS, 664x524 at 60 FPS (2x2 pixel
binning),
640x480 at 60 FPS (center cut-out mode)
Triggered acquisition: Frame rate is half the specified rate. Maximum frame rate in external trigger mode: 30FPS
|
|
Partial Image Modes |
pixel binning and region of interest modes via Format_7 |
pixel binning or center cut-out (640x480) mode via Format_7 |
|
General Purpose I/O Ports |
7-pin JST GPIO connector, 4 pins for trigger and strobe, 1 pin +3.3 V, 1 Vext pin for external power |
|
Gain Control |
automatic / manual, 0 dB to 12 dB |
automatic / manual, 0 dB to 24 dB |
|
Shutter Speed |
automatic / manual, 0.12 ms to 512 ms |
automatic / manual, 0.03 ms to 8000 ms |
|
Gamma |
0 to 1 (enables 12-bit to 10-bit companding) |
0.5 to 4.00 |
|
Synchronization |
via external trigger, software
trigger (on same bus only), or free-running* |
via external trigger |
|
External Trigger Modes |
IIDC v1.31 Trigger Modes 0 and 3 |
|
Power Requirements |
8 to 30 V via IEEE-1394, less than one (1) Watt |
4.75 to 5.25 V via the Mini-B USB 2.0 or GPIO connector, less than one (1) Watt |
|
Dimensions (LxWxH) |
24.4 x 44 x 34 mm |
|
Mass |
37 g (including tripod adapter) |
|
Camera Specifications |
IIDC 1394-based Digital Camera Specification v1.31 |
|
Memory Storage |
three memory channels for user configurable power-up settings |
|
Lens Mount |
CS-mount (5mm C-mount adapter included) • M12 microlense mount |
|
Compliance |
CE, FCC Class B, RoHS |
|
Operating Temp |
0° to 45°C |
|
Storage Temperature |
-30° to 60°C |
|
Warranty |
1 year |
|
Configuration Options |
board-level** • microlens** • mini 1394 connector**• metal case |
| *Using standard non-Format_7 video formats and modes operating at 30 FPS and 60 FPS only. |
| **For qualified OEMs |
Development Kit Contents
The following items are included in the Firefly MV FireWire Development Accessory Kit DEVKIT-01-0005:
- ACC-01-2002: 2 meter, 6-pin to 6-pin, ultra-thin IEEE-1394 cable
- ACC-01-1000: IEEE-1394 OHCI PCI Host Adapter 3 port-400 Mbps card
- ACC-01-3002: Male GPIO connector pre-wired for quick and easy access
The following items are included in the Development Accessory Kit DEVKIT-01-0003:
- 2 meter USB 2.0 cable (Type A to Mini-B 5-pin)
- ACC-01-3002: GPIO wiring harness
- Firefly MV and Chameleon Getting Started Manuals
Emissions and RoHS Compliance
FCC / CE Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off or on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
RoHS / WEEE Compliance
This product is RoHS and WEEE compliant.
View catalog
