"C/M" indicates both monochrome and color sensor options are available for this part number. Full part numbers are available here http://www.ptgrey.com/sales/models.asp.
Grasshopper2
Model#
|
GS2-FW-14S5M/C-C |
|
Image Sensor Type
|
Sony® ICX 285 2/3"progressive scan CCD |
|
Image Sensor Model |
ICX285 2/3” (EXView HAD) |
|
Max Resolution
|
1384x1036 |
|
Pixel Size
|
6.45 x 6.45µm |
|
Analog-to-Digital Converter
|
Analog Devices 14-bit ADC
|
|
Video Data Output
|
8, 12, 16 and 24-bit digital data
|
|
Image Data Formats
|
Y8, Y16 (all models), RGB, YUV411, YUV422, YUV444, 8-bit and 16-bit raw Bayer data (color models)
|
|
Digital Interface
|
Dual Bilingual 9-pin IEEE-1394b for camera control, video data transmission, and power
|
|
Transfer Rates
|
100, 200, 400, 800 Mbit/s
|
|
Max Frame Rate |
1384x1036 at 30fps |
|
Partial Image Modes
|
pixel binning and region of interest modes via Format_7
|
|
General Purpose I/O Ports
|
8-pin Hirose HR25 general purpose input/output connector
4 pins for external trigger, strobe or RS232 / 1 pin +3.3V / 1 VEXT pin to externally power the camera
|
|
Gain Control
|
automatic / manual / one-push gain modes, programmable via software -3.6dB to 24dB in 0.04dB increments
|
|
Shutter Speed
|
automatic / manual / one-push modes, programmable via software 0.03ms to greater than 330s (extended shutter mode)
|
|
Synchronization
|
via external trigger, software trigger, or free-running
|
|
External Trigger Modes
|
DCAM v1.31 Trigger Modes 0, 1 (bulb shutter), 3, 14 (overlapped trigger and transfer), and 15 (multi-shot trigger)
|
|
Voltage Requirements
|
8-30V, via the IEEE-1394b interface or Hirose 8-pin GPIO connector
|
|
Power Consumption
|
less than 2.5W |
Dimensions
(L x W x H) |
58mm x 44mm x 29mm (not including lens holder and GPIO connector) |
|
Mass
|
104g (without optics)
|
|
Camera Specification
|
IIDC 1394-based Digital Camera Specification v1.31, compatible with IEEE-1394b and IEEE-1394a interfaces
|
|
Lens Mount
|
C-mount
|
|
Emissions Compliance
|
Complies with CE rules and Part 15 Class A of FCC Rules
|
|
Operating Temperature
|
0° to 40°C
|
|
Storage Temperature
|
-30° to 60°C
|
|
Vibration Resistance
|
10 G (14 Hz to 200 Hz)
|
|
Warranty
|
2 year
|
Development Kit Contents
The following items are included in the Flea2 / Flea3 / Grasshopper / Grasshopper2 / Grasshopper Express / (1394b models only) Development Accessory Kit DEVKIT-01-0001:
- ACC-01-2006: 4.5 meter, 9-pin to 9-pin locking IEEE-1394b cable
- ACC-01-2007: 4.5 meter, 6-pin to 9-pin locking IEEE-1394a to 1394b cable
- ACC-01-1001: IEEE-1394b OHCI PCI Host Adapter 2 Port 800Mbps card
- ACC-01-3000: Hirose HR25 8-pin male GPIO connector with 1m wiring harness
The following items are included in the Flea2 / Flea3 / Grasshopper / Grasshopper2 / Grasshopper Express / (1394b models only) Development Accessory Kit DEVKIT-01-0002:
- ACC-01-2006: 4.5 meter, 9-pin to 9-pin locking IEEE-1394b cable
- ACC-01-2007: 4.5 meter, 6-pin to 9-pin locking IEEE-1394a to 1394b cable
- FWB-PCIE-01: FirePRO low profile single bus IEEE-1394b PCI Express card
- ACC-01-3000: Hirose HR25 8-pin male GPIO connector with 1m wiring harness
Emissions and RoHS Compliance
FCC / CE Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off or on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
RoHS / WEEE Compliance
This product is RoHS and WEEE compliant.
View catalog
